"Our job is helping you do your job"
800.544.2843Email 
  • UPC5000

    Standard Features:

    • Available in self-contained enclosure with carrying handles (UPC5000) or 19” wide rack-mountable version (UPC5010)
    • Six sets of ranges to choose from: 2000/1000/400 psi, 1000/500/200 psi, 500/250/100 psi, 100/50/20 psi, 50/25/10 psi, and 15/7.5/3 psi
    • Three independent selectable ranges in each instrument
    • ±0.05% F.S. accuracy of each independent selectable range
    • Available with Light Emitting Diode (LED) or Liquid Crystal Display (LCD)
    • Pressure display resolution 0.02% F.S. typical for each range
    • State-of-the-art push button calibration-No analog potentiometers or adjustments required
    • Lightweight, less than 33 pounds
    • Adjustable overpressure protection
    • Precision pressure vernier control
    • Self-contained 2215 psi nitrogen cylinder
    • Voltage/current display mode for transducer testing
    • Supplies DC loop power
    • Non-destructible, finger tip control micro-metering valves for pressure control
    • Quick-disconnect fitting and hose included
    • Different technicians can calibrate the same Device-Under-Test and get identical results…every time
    • Calibration Certficate included-traceable to the National Institute of Standards and Technology (NIST)
    • Pneumatic only-no hydraulic fluid or distilled water messes

     

  • UPC5000 Accessories Group Pic
  • UPC5100-UPC5110

    Standard Features:

    • Available in self-contained enclosure with carrying handles (UPC5100) or 19” wide rack-mountable version (UPC5110)
    • Five independent selectable ranges in each instrument ±0-28 inHg, ±0-387 inH₂O, 0-2771 inH₂O, ± 0-96 kPa, 0-100 PSI
    • Available with Light Emitting Diode (LED) or Liquid Crystal Display (LCD)
    • Pressure/Vacuum display resolution 0.02% F.S. typical for each range
    • ±0.05% F.S. accuracy for each range
    • State-of-the-art push button calibration-No analog potentiometers or adjustments required
    • Different technicians can calibrate the same Device-Under-Test and get identical results…every time
    • Easy to operate, training can be accomplished in 10 minutes
    • Lightweight-less than 35 pounds
    • Adjustable overpressure protection
    • Precision vernier control
    • Self-contained nitrogen cylinder and vacuum converter provides 27 inches Hg (without external pump) to 100 psi
    • Voltage/current display mode for transducer testing
    • Quick-disconnect fitting and hose included
    • Pneumatic only-no hydraulic fluid or distilled water messes
    • Calibration Certficate included-traceable to the National Institute of Standards and Technology (NIST)

  • UPC5100 Accessories
  • UPC5200 & UPC5210

    Standard Features:

    • Available in enclosure with carrying handles (UPC5200) or 19” wide rack-mountable version (UPC5210)
    • Two sets of ranges to choose from: 10,000/5000/2000 psi and 5000/2500/1000 psi
    • Three independent selectable ranges in each instrument
    • ±0.05% F.S. accuracy of each independent selectable range
    • Available with Light Emitting Diode (LED) or Liquid Crystal Display (LCD)
    • Pressure display resolution 0.02% F.S. typical for each range
    • Different technicians can calibrate the same Device-Under-Test and get identical results…every time
    • Electronically controlled 10:1 intensifier system-Easy to operate, training can be accomplished in 10 minutes
    • Easy to carry-approximately 51 lb.
    • Adjustable overpressure protection above input pressure
    • Precision pressure vernier control
    • Voltage/current display mode for transducer testing
    • 32 VDC excitation output
    • Non-destructible, finger tip control micro-metering valves for pressure control
    • Automatic pushbutton calibration, microprocessor controlled and maintained
    • Quick-disconnect fitting and hose included
    • Pneumatic only-no hydraulics or distilled water messes
    • External portable pressure cylinder included with UPC5200
    • Calibration Certficate included-traceable to the National Institute of Standards and Technology (NIST)

  • UPC5200 Accessories
  • Condec 3030

    This is a discontinued item. Please go to Martel Electronics BetaGauge 311A/321A Advaned Pressure Calibrators for an equivilent product.

    Standard Features:

    • Many models and external modules available (contact factory for additional items)
    • 4 AA cells included, > 35 hours, typical usage
    • Ranges from vacuum to 10,000 psi, -15 to 15 psi, -15 to 30 psi
    • 0.025% of full scale for models with 15 psi thru 3000 psi internal pressure ports
    • 0.015% measurement of 0-24 mA or 0-10V
    • RS-232/External pressure module port standard
    • High-contrast back lit Liquid Crystal Display (LCD), up to 3 process sub-regions
    • Multi-engineering units standard: psi, bar, mbar, kPa, mPa, kg/cm², mmH₂O @ 4˚C, mmH₂O @ 20˚C, cmH₂O @ 4˚C, cmH₂O @ 20˚C, inH₂O @ 4˚C, inH₂O @ 20˚C, inH₂O @ 60˚F, mmHg @ 0˚C, inHg @ 0˚C
    • Built-in stainless steel sensor for gas and liquid compatibility, 1/8-27 NPT female pressure port
    • Operating temperature -10 ˚C to 50 ˚C (14 ˚F to 122 ˚F)
    • Switch test on pressure 1, pressure 2 or external pressure module
    • Built-in damping function
    • Minimum/Maximum pressure readings
    • Percent error displayed
    • Built-in 24 VDC power supply to power unit under test
    • Instrument setup recall, 5 last used on power-up
    • Calibration Certificate included-traceable to the National Institute of Standards and Technology (NIST)

     

    Notes on Specifications

    • Noted gauge and absolute pressure ranges are for isolated stainless steel pressure ports except those noted with an (*).
    • Stated pressure accuracies are for internal pressure ports only.
    • Consult factory for external pressure modules.
    • Specifications 18 ˚C to +28 ˚C, unless otherwise noted.

  • Condec 3030 Accessories
  • MPV-10K

    Applications

    • Gas and fluid applications
    • High purity systems
    • Medical and Bio-chemical gas analysis
    • Natural gas systems
    • Semi-conductor production
    • Pollution analysis instrumentation
    • Process plant instrumentation
    • Solvent systems
    • Chromatography
    • Mass spectroscopy
    • Research laboratory sampling
    • Oxygen service
    • Machine cutting tools

    Standard Features

    • Fine micro-metering valve with positive shut off
    • Adjustable stop, soft seat, No over-tightening
    • Stainless Steel
    • Finger tip adjust – even at 10,000 psi
    • Viton O-rings standard; other materials available by request
    • Valve can be panel or bracket mounted

  • Image
  • Condec Regulator Pressure Reducing Gas

    Standard Features

    • Same quality regulator as used in the Portable Pressure Calibrators
    • Low torque required by operator for pressure adjustment
    • Single Stage, Venting Type with spring controlled piston
    • Integral inlet filter used to promote long life when used in clean systems
    • Adjustable Panel Mounting
    • May be integrated with one of our Burst Discs and/or Pressure Relief Valves for FAIL SAFE operator safety when installing in a system.  When integrated with one of our CONDEC patented finger-tip-adjustable Orion Series or MPV Needle Valves, you will have the advantages of proper regulation of your source, as well as precise finger-tip adjustment of your downstream system output

  • Cylinder Regulator

    Standard Features

    • Same Condec “REG” series regulator as used in our Portable Pressure Calibrators and Source 3000
    • Low Torque required by operator for pressure adjustment
    • Single Stage, Venting Type with spring controlled piston
    • Integral inlet filter used to promote long life when used in clean systems
    • CGA-580 fitting for direct connection to the In-House cylinder
    • ¼ inch 37 degree male output port connection

     

    Applications

    • Gas applications
    • In-House nitrogen cylinder regulation

  • Image
  • PIN7000 & PIN7010

    Standard Features

    • Available in self-contained enclosure with carrying handles (PIN7000) or 19 inch wide rack-mount version (PIN7010)
    • Internal precision pressure intensifier generates up to 10 times input pressure
    • Electronically controlled intensifier system
    • Precision Condec REG1000 (regulator) to adjust input pressure
    • Three gauges to monitor regulated pressure, accumulated pressure, and output pressure
    • Patented micro-metering valves for precision pressure adjustment and venting
    • Quick-disconnect fittings and hoses supplied for input and output pressure
    • Easy to operate, training can be accomplished in 10 minutes
    • Different technicians can operate the system and get identical results…every time
    • Pneumatic only – no hydraulics or distilled water messes

    Applications

    • High pressure supply, up to 10,000 psi, for test equipment
    • Ideal for fluid-free high pressure calibration
    • Works with all major manufacturer’s electronic pressure calibrators

  • PIN8000 & 8010 Accessories
  • PIN8000

    Standard Features

    • Available in self-contained enclosure with carrying handles (PIN8000) or 19 inch wide rack-mount version (PIN8010)
    • Internal precision pressure intensifier generates up to 10 times input pressure
    • Electronically controlled intensifier system
    • Two output (test) ports, for connecting to Device-Under-Test as well as a precision calibration standard (works with all major brand pressure calibrators, digital gauges or indicators)
    • Precision Condec REG1000 (regulator) to adjust input pressure
    • Three gauges to monitor regulated pressure, accumulated pressure, and output pressure
    • Patented micro-metering valves with vernier for precision (.0005 psi) for pressure adjustment and venting
    • Quick-disconnect fittings and hoses supplied for input and output pressure
    • Easy to operate, training can be accomplished in 10 minutes
    • Different technicians can operate the system and get identical results…every time
    • Pneumatic only – no hydraulics or distilled water messes

    Applications

    • High pressure supply, up to 10,000 psi, for test equipment
    • Ideal for fluid-free high pressure calibration
    • Works with all major manufacturer’s electronic pressure calibrators

  • PIN8000 & 8010 Accessories
  • UVC1000_UVC1010

    Standard Features

    • 2 modes of operation: vacuum or pressure
    • 29 inches Hg vacuum from shop air supply
    • Lightweight design
    • Built-in vacuum converter and pressure regulator
    • Availabe as standard (UVC1000) or 19 inch wide rack-mount version (UVC1010)

    Applications

    • Hazardous environments
    • Source for calibration of compound gauges
    • Low-cost alternative to vacuum pump
    • Need for precise vacuum or pressure control

    Note:
    At input pressures less than 100 psi, vacuum level may be less than 29 inches Hg.

  • 55291
  • Orion 2C

    Features:

    • System working pressure:

                Orion 2C, non-cased/cased versions:

                Up to 3000 psi

                Orion 3A, non-cased version: Up to 10,000 psi

                Orion 3A, cased version: Up to 10,000 psi based on model

    • Orion 2C: Aluminum body, Buna-N

                O-Rings Standard

                Orion 3A: Stainless Steel Body, Viton

                O-Rings Standard

    • Precision patented vernier to precisely “dial in” a selected pressure
    • Fingertip closed system pressure adjustment to better than 0.0005 psi
    • Soft seat construction and adjustable stop-immune to over tightening
    • Two low-torque, fine micro-metering valves with positive shut off
    • Two test ports allow for multiple applications
    • Non-cased Models
    • Cased models, # of test ports based on version

     

    Applications:

    • Gas applications
    • Operation to 10,000 psi, based on model
    • Test stands
    • OEM pressure control applications

  • 120422 & 120462
  • Source 3000

    Features:

    • Self-contained nitrogen cylinder
    • “Overpressure protection” Condec REG 3000 regulator limits pressure to costly units under test
    • Charge your internal nitrogen cylinder to 3000 psi with provided adapter fitting
    • Two output (test) ports, for connecting to Device-Under-Test as well as a precision calibration standard (works with all major name brand pressure calibrators, digital gauges or indicators)
    • Precisely dial into required pressures with patented valve assembly
    • 15.2 cubic feet of nitrogen at 3000 psi
    • Aluminum carrying case
    • Front panel gauges inform operator of internal cylinder pressure level
    • Different technicians can operate the system and get identical results…every time
    • Pneumatic only – no hydraulics or distilled water messes

    Applications:

    • Works with all major manufacturer’s electronic pressure calibrators
    • Truly portable pneumatic source to 3000 psi
    • Nitrogen source for a full day of calibrating

     

  • Source 3000 Accessories